Followers

Pages

Thursday, December 22, 2016

Stretch your Planner Stickers


Hello everyone! This is Deepti and welcome back. Today I'm focusing on Insta Quote stickers. These are meant for planners but you can stretch these and can use on your cards. These stickers add a trendy and posh look to your cards.

Today, I'm going to show you three different ways of using these stickers on your cards. So let;s get started!


Creating a story or scene : This card is pretty simple. This cute little dog is following his dreams and he is reaching out for a dough nut! He is just following his heart and dreams!! Conveying the message in a simple way!


Creating a Pattern Paper : I chose all the stickers that has pretty patterns and stick it on a piece of card stock forming an unusual pattern. Voila! Your own DIY background is ready.



Simple Pop up cards : Yes! you can create some inspiring and encouraging pop up cards. :)

These are just a few card ideas but you can make many more out of these. The sky is not the limit! Just go for it and explore and share your beautiful ideas with us.

Thank you so much for stopping by. See you again! :)

Sunday, December 18, 2016

Let's spin and slide!

Hello crafty friends,

I am here with some slider and spinner card. It is quite a trend lately but I never tried them before. I always thought that it is easy if you have right type of dies. So when Priya sent me this Spinner card dies by Nellie Snellen, I was thrilled to try my hands at it!

There are 3 dies which are to create the slit/channel for your sliding or spinning object, 1 is to make pinwheel and two circle dies are there to make the mechanism behind spinning object.

Assembling a slider card is not at all difficult. The time consuming part is thinking about stamps and dies to use. You need to select a focal point element and sentiment very carefully. It should justify  the movement of a slider / spinner card. 

For the first card, I used Altenew's Stick Figure stamp set.  I selected the image where a man is pushing a huge rock and so i can show the movement - pushing, moving ! 





Let's see step by step how I made it.



I took a little smaller panel of Bielo CS than my base card (a2). I masked and created ground and sky with distress inks. I made a slope to make the message more effective. I also stamped stick figure with a rock on a card stock and fussy cut it and also blend inks on it so it will merge with background and will become part of scene. 

                             

Next, I took another smaller panel which will go behind the slit, inked it to match the front panel and used my MISTI to position my sentiment exactly in that slit so it will be visible when the stick figure and rock is moved.

                    

See how I lifted the panel with 3d foam tape to give room for the slider disc to move. For the slider part I cut a circle (its diameter has to be larger than slit width) and stacked 2-3 stripes of card stock slightly narrow than slit which will allow the sliding part move freely. Now, mount the main panel on the one with sentiment while sandwiching the slider disk in the slit. Adhere the stick figure and rock cutout on that sliding stripe with glue. Mount the whole circus on a base card. Check the video to see it in action.





Isn't that fun?

Now let's check the second card!


Watch the video first to see it in action. That will give you better idea of construction of spinning pinwheel.






So, let's start step by step.
I took a top fold A2 size Bielo card base, smooshed some dye base ink from top left corner. Once the ink was dry did same stroke with versamark ink pad and heat embossed it in Brutus Monroe silver embossing powder. Cut heart shape and pin wheel from some pattern paper. 


I used these round 3d, double-sided  foam dots, a brad and a twine to build pinwheel spinner.


Sandwich the twine between two sticky side two foam dots. Adhere it to the back of pinwheel while piercing it with a brad. Keep the top backing paper intake.  


Glue the heart diecut on the base & punch a hole with a needle tool. Pass the brad of pinwheel through the hole and secure it from the back of the card front. I adhered a red heart which says 'pull here' at the end of the twine for that finishing touch.Your spinner is ready. Just wrap the twine around pinwheel and pull to spin it.

Die cut 'YOU" from a black glitter foam. Rest of the sentiment is made using Dymo Lable Embosser.
I love this tool as it is very useful to create your own sentiments. 

Are you still with me?

Moving to the last card....




For this card I meant to use that wavy  slider die to imitate the waves of sea. But when I realized that I switched the die by mistake, it was too late. 
I have used pattern paper for the lower half of the panel.




I hope you enjoyed the post and my creation. Give it a try, it is truly fun. Keep in mind to choose stamp carefully to make your cards more effective.


Wednesday, December 14, 2016

Jewelry with Metal Stamping

Hello Peeps

I am back again with another post and this time with something new I have ever tried. Yes, I will be sharing ideas, tips and techniques on yet another form of jewelry making tool available exclusively with the CraftShop. And this Metal Stamping. I am just a beginner and sharing everything that worked best for me. And it requires practice to get the perfect results !


What is Metal Stamping ?
Metal Stamping simply means stamping on metal as we stamp on paper. It is a great way to share your heartfelt messages with your friends, loved ones, and the world. It is an amazing way of creating customized jewelry.

What are Metal Stamps ?
To do metal stamping with hand you need metal stamps. Metal stamps are solid rods with alphabets and numbers on one end and it is flat on other end.  They come in variety of sizes like 3mm, 5mm and in upper and lower cases. The image below shows how it actually looks –


Metal Stamping Tools -

Metal Stamping tools includes –

1. Metal Stamps
2. A very smooth and hard surface that can take some banging. This is the surface where you will place your metal blanks to be stamped. I tried stamping on heavy wooden log and iron block too. Both worked for me. Avoid using floor as stamping surface, chances of damaging it with hammer. Also avoid concrete floor as metal blanks will get concrete impression on back side. So whatever surface you choose, it has to be hard and smooth.
3. A metal hammer with a flat face. I use a regular hardware-store hammer. A fairly heavy hammer that’s still comfortable for you to use can make your stampings turn out better
4. Permanent markers (like Sharpie), in black and / or any other colors you wish. I am using a CD marker
5. A pencil or a sketch pen for drawing lines
6. Masking tape, painter’s tape, or post-it note
7. Tissues or soft cloth
8.  Metal Blanks


Prepare you Metal Stamps –

I recommend drawing a line on metal stamps using marker or acrylic colors. The line is drawn in the center on a side. This will help in stamp alignment on metal surfaces while stamping as the line which you will draw actually divides letters in two parts. And you can take this line as your reference point. Make sure you mark the side which makes letter appear right on stamping surface; you don’t have to choose right direction every time as a result. Thus, saving your time!
You can also write the stamp’s letter or number on stamp. This will help in picking letters quickly for stamping. And will make your future tasks easier too. Refer to this image


How to do Metal Stamping

Metal Stamping can be done on variety of metals – aluminum, brass, iron, stainless steel etc. Metals differ in hardness. You can start with aluminum as it is softer and takes a good impression and is inexpensive. You can try your hand on some household items. Washers are a good for starters.
I too first stamped on washers. You will get an idea of the pressure with which the hammer is hit on the metal stamp.

I am explaining a tutorial on stamping on metal blanks which are rectangular/square -

1. Take you stainless steel blank. Remove its bail. Measure it dimension (image 1). Plan whether you want to stamp horizontally or vertical. 
2. Use a pencil or sketch pen to draw a line in center. (image 2). 
3. Write your text on paper and arrange your metal stamps in order accordingly. (image 3 & 4)
4. Place your stamp on hard, smooth surface. Tape it down so it doesn’t move when hammered. (image 5)
5.  Now draw lines at equal distance on metal blank. If your word is say “blessed”, then you need to draw 7 lines at equal distance. You can use a ruler for this. If you are planning to add some charms while finishing off your pendant then start stamping first letter at a distance from the top. Or if you want to add some charms/embellishments at the bottom then leave space for them beforehand. You need to plan these things first for stamping. (image 6)
6.  Extend lines on tape so that it is easier to align stamp
7. Hold the metal stamp with the text facing you (letter written in yellow colour facing you, image 7 )and the flat end up. Hold the metal stamp firmly at the base. I holded the stamp slightly in the middle for shooting purpose. Align the stamp line with the line on the metal blank. (image 7)
8. Now give a nice tap with hammer. Use a heavy hammer for stainless steel. Hit each stamp once with your hammer. You can even hit more than once but be careful not to move your metal stamp; otherwise you’re likely to get blurred or double images.
9. To pop the letters, coat them with black permanent marker. Then wipe off the excess with tissue or cloth.


Stamping on round or curved surface

If you are stamping on round surface then you use these tips for stamping

1.       Place your blank on hard, smooth surface and tape it down. (image 1)
2.       Arrange you metal stamps in order. (image 2)
3.       I am stamping “Be Happy”. So draw lines at equal distance. I am marking small dots on each line where I will be placing my stamps. Check the red encircled mark on image. (image 3)
4.       Pick your metal stamp. You can start with any letter. Align the stamp line with the line on blank and don’t go beyond dot.(image 4)
5.       Now give a nice tap with hammer.
6.       Coat with acrylic color or marker and wipe off the excess with tissue.

This is the finished pendant –

I stamped on this heart shaped metal blank. The metal is relatively soft so it needs hammering with less pressure. Holding stamp with shaky hands will result in misalignment (letter V).



And the finished one –


Some more –






Some Useful Tips –
1.       Metal stamping takes practice and with practice you will get better.
2.       Use inexpensive items first to test and use the front and back for even more practice.
3.       Always relax while stamping


That’s all for today.  I hope you like my maiden attempt at Metal Stamping. I still need more practice. Do give it a try. And for queries, leave a comment.
Thank you for stopping by. See you next time !!!

Till then
Happy Crafting
Poornima

http://papercrafthorizon.blogspot.in/

Friday, December 9, 2016

Calender in a box

Hi friends,
Year 2016 is almost over and we all are getting ready to welcome 2017 . The craft companies gave us have some amazing products to enjoy and I hope the same will happen in 2017..
Looking forward for an enriching and creative year ahead.
So lets get started for today's post,
I got a book box by Graphic45

Each Book Box includes a coordinating 3 piece tag album with binder ring.
Book Box (7.125 x 5  x2.5 in)
Regular Tag Album (5.75 x 3.875in) 

so this is a very sturdy and neat book box which you can use to hold you mini albums, gifts, jewellery, keepsakes etc..
I somehow wanted to give it a new look and functionality and hence I transformed this into a calendar. You can make a bunch of these with scraps of paper and its a perfect gift for new year.
I really don't enjoy making the box structure and working with chipboard ...its kinda difficult and nuclear science for me. So if u are like me just grab this amazing box decorate and embellish it (which is my favourite part ;) I am sure u will feel happy and satisfied by the masterpieces you will create.

Here are some pictures






ok ..so now I have a video showing u what exactly I did to this box and made a calendar.
watch it at youtube


I hope you will try this project and do not forget to share the pictures with us at our FB page and other social media.

see you soon
hugs
Arjita


Supplies:
Graphic 45 Book box
Paperpad 12X12 by Papericious- The flora Season
Big shot machine
Scalloped circle Die
Tonic Trimmer
ATG glue gun
Scissors
Tombow Glue
Chipboard
Thick cardstock


Tuesday, December 6, 2016

Tack N' Peel Reusable Cling Sheet

Hello everyone! This is Deepti here with a new post about Tack N' Peel Reusable Cling Sheet.


  • Tack n' peel is a cling sheet from Tsukineko is a unique, reusable products designed for creating a Stamping Block.
  • It has a yellow cover on one side and a clear sheet on the other side
  • This can be used on acrylic or clear blocks. The adhesive layer provides a strong bond for unmounted rubber stamps
  • However you can obviously stick it to any surface as it holds any object firmly like rubber bands, plastic wraps, bubble wraps, foam and etc.

  • The adhesive layer can be easily preserved by simply rinsing the surface with water and then air drying - stickiness restores over and over again!

HOW TO USE
  1. Simply measure the tack n peel to the size of your clear block and trim it
  2. Next, peel off the yellow wrapper and adhere it onto the acrylic block
  3. Then peel of the clear sheet and mount your unmounted rubber stamps and enjoy stamping
  4. Once your stamping was done secure the clear sheet over the acrylic block for future use

If you have any questions regarding this process kindly leave us a comment down below and we will get in touch with you as soon as we can. Thanks and happy paper crafting!

Saturday, December 3, 2016

Hi Crafty Friends,

This is Smita here.I am so excited to share this introduction cum tutorial with you all.Thanks Priya for this chance.
I have been working with polymer clay since last year.Polymer clay is a very good medium to work with and the quality of the end product is very reliable.
What is Polymer clay?
Polymer clay is a type of hardenable modeling clay based on the polymer polyvinyl chloride(PVC). It typically contains no clayminerals, but like mineral clay a liquid is added to dry particles until it achieves gel-like working properties, and similarly, the part is put into an oven to harden, hence its colloquial designation as clay. Polymer clay is generally used for making arts and craft items, and is also used in commercial applications to make decorative parts.

I would like to give few examples of  how this clay can be used.

Things needed to start with:
Clay-Premol,sculpey,Fimo
Some kind of rolling pin recommended acrylic
Cutters
A tile or glass surface

A simple pendant tutorial:                                   


1.Things needed
2.Condition your clay by pressing in between your fingers .

3.Roll it using acrylic roller and cut it into required shape as shown in 4.


1.Take some scrap clay and and mould it into your required shape(dome shape as shown in 2)

3.Place the rolled clay onto the scrap dome and cut the excess as shown in 4.


1.Press the layer firmly onto the dome.

2.Condition some black clay and roll and cut into required shapre using cutter or mould it using your hand(shown in pic 2,3,4)


Arrange the embellishments using your creativity and insert an eyepin .Finally it's ready to go into oven.

Before I give few other examples..here are few tips that I have learnt from my experience:
Tips:
1.Baking instructions would different for different brands so please follow the instructions on the cover.
2.Sanding and buffing is mainly done for non texture products like beads ,cabochons.
3.While using white clay clean your hands
4.Pasta machine can be used to roll the clay and to make shades.
5.If clay is too hard use vegetable oil or clay softner while conditioning.
6.Keep the thickness of the clay around 3-4 mm
7.Use stamps to create texture.




Make your own embellishment like this flower below:

Using Plungers/cutters u can make your own embellishments for scrapbook and cards. As shown in this above pic.


In the next photo you can see how I made a peppa pig pendant for my daughter.Finally in the last pic you can see the baked and glazed products.Before glazing if the product u made doesn't have any texture sanding and buffing will give a very nice glaze and a liquid glaze at the end would be cherry on top.


The next example shows a Peppa pig pendant that I made for my daughter for her birthday.


this is how it looks after baked and glazed.

 Finished products:
Hope you all enjoyed this small introduction and tutorial about polymer clay and hope to see some awesome creations from you all.
Polymer clay and few cutters used fro Priya's store-Color conceptions.
Thanks,
Hugs,
Smita